Now many buildings are using color steel tile roof, color steel machinery has a single layer and sandwich. Some people say that the single-layer color steel tile steams people in summer, which is too hot for people to bear. It’s not insulated in winter, and it’s too cold. Even if it’s made of smallpox, it’s not good. In fact, using single-layer color steel tile press in summer will have a simple way to cool down.

Refer to the following placement points:

(1) for the convenience of operation and maintenance, please be more than 50cm away from the wall.

(2) then fine adjustment: the machine platform shall be leveled to maintain the precision.

(3) Secondly, the following matters are important for the installation of foundation: a strength must be able to follow the weight of the machine; B base surface must be flat

(4) installation of color steel equipment (refer to instructions)

(5) finally, a place with good power supply

There are two fixing methods for the installation of color steel machinery and equipment: through type and concealed type. Through type fixing is the most commonly used method for the installation of color steel equipment on the roof and wall, that is, the color plate is fixed on the support (such as purlin) with self tapping screws or rivets. Construction technology and operation points of color steel tile pressing equipment
First, there are two ways to fix the installation of color steel mechanical equipment: through type and concealed type. Penetrating fixation is the most common way for installation of roof and wall color steel equipment, that is to use self tapping screws or rivets to fix color plates on supports (such as purlins). Penetrating fixation is divided into wave crest fixation, wave trough fixation or their combination. Concealed fixing of concealed fastener is a fixing method that the special fastener matched with the concealed fastener color plate is fixed on the support (such as purlin) first, and the main rib of the color plate and the central rib of the concealed fastener are toothed, which is generally used for the installation of roof panel.

Second, the lateral and end lap of the color plate. When installing each steel plate, the edge lap shall be accurately placed on the previous steel plate and clamped with the previous steel plate until both ends of the steel plate are fixed. A simple and effective method is to clamp the overlapped steel plates with a pair of pliers.

Third, in the south, the color board is generally designed as a single-layer color board. In order to reduce the solar radiation heat entering into the building, when installing the roof panel, the thermal insulation layer can be installed in the roof system. There is a very simple, economic and effective method, that is, before the installation of roof steel plate, the purlin or slat is covered with double-sided reflective foil film, which can also be used as steam isolation to reduce cohesion. If the sagging depth of the film between supports is allowed to reach 50-75mm, the air layer between the film and the roof panel will further improve the heat insulation effect.

Fourth, the selection of self tapping screw. When selecting fixing screws, the fixing parts shall be selected according to the service life of the structure, and special attention shall be paid to whether the service life of the covering material is consistent with that of the specified fixing parts. At the same time, the thickness of steel purlin shall not exceed the self drilling capacity of screw. The screws currently available can have plastic heads, stainless steel covers or be coated with a special durable protective coating. In addition, in addition to the screws for snap fixing, all other screws are provided with waterproof washers, and the corresponding special washers are provided for the lighting panel and special wind pressure.

Fifthly, it is easy to master the installation of color steel profiler – color plate, and the treatment of some details is more important. For the roof color plate, the color plate should be closed at the roof and eaves to prevent rainwater from entering the roof more effectively. At the ridge of the roof, the outer plate of the roof can fold up the chassis between the end ribs of the steel plate with the edge closing tool. It is used at the upper end of all roof steel plates with a slope of less than 1 / 2 (250) to ensure that water blown by the wind under the flashing or cover plate will not flow into the building.
Sixth, in the design of large-span and large-area factory buildings, in order to have enough brightness, daylighting belts are often designed, which are generally arranged in the middle of each span. Although the setting of the lighting board increases the lighting degree, it also increases the heat transfer of the sun and the temperature in the building.